Difference between revisions of "HiFiBerry Amp 2"
From Autopilot Wiki
Line 8: | Line 8: | ||
The HiFiBerry Amp 2 is an integrated amplifier and sound card capable of playing audio at 24 bits/192kHz. The Amp 2 is a HAT peripheral that mounts on top of the Raspberry Pi, uses the [[Uses Protocol::I2C]] protocol, and powers the Pi through its 5V rail. | The HiFiBerry Amp 2 is an integrated amplifier and sound card capable of playing audio at 24 bits/192kHz. The Amp 2 is a HAT peripheral that mounts on top of the Raspberry Pi, uses the [[Uses Protocol::I2C]] protocol, and powers the Pi through its 5V rail. | ||
− | |||
− | |||
== Configuration == | == Configuration == | ||
− | In | + | In '''/boot/config.txt''', remove or comment out the following to disable the built-in audio<ref>https://www.hifiberry.com/docs/software/configuring-linux-3-18-x/</ref>: |
<pre>dtparam=audio=on<pre> | <pre>dtparam=audio=on<pre> |
Revision as of 04:02, 31 December 2020
HiFiBerry Amp 2 | |
---|---|
Modality | |
Part Type | |
Manufacturer | |
Product ID/Part Number | |
Product Page |
|
The HiFiBerry Amp 2 is an integrated amplifier and sound card capable of playing audio at 24 bits/192kHz. The Amp 2 is a HAT peripheral that mounts on top of the Raspberry Pi, uses the I2C protocol, and powers the Pi through its 5V rail.
Configuration
In /boot/config.txt, remove or comment out the following to disable the built-in audio[1]:
dtparam=audio=on<pre> And add the line: <pre>dtoverlay=hifiberry-dacplus
GPIO Usage
The following pins are reserved and can't be used for other purposes[2]:
Board Pins | BCM # | Use |
---|---|---|
3, 5 | 2, 3 | I2C Configuration |
12, 35, 38, 40 | 18-21 | Sound interface |
7 | 4 | Mute -- pulling low mutes (so pull it up!) |
Specs
Recommend powering with an 18V power supply!
Recommended operating voltage | 12-20V | |
Absolute maximum operating voltage | 24V | |
Maximum output power | 60W | |
THD+N | <0.02% | typical, output power 0.1-10W |
SNR | 104db | typical |
Frequency response | 20-20000Hz | output filter characteristics depending on specific speaker parameters |
Typical output power per channel | 14W | Vsupply=12V, Rspk = 4Ohm, THD+N <0.1% |
18W | Vsupply=18V, Rspk = 4Ohm, THD+N <0.1% | |
20W | Vsupply=24V, Rspk = 4Ohm, THD+N <0.1% | |
8W | Vsupply=12V, Rspk = 8Ohm, THD+N <0.1% | |
17W | Vsupply=18V, Rspk = 8Ohm, THD+N <0.1% | |
28W | Vsupply=24V, Rspk = 8Ohm, THD+N <0.1% | |
Maximum output power per channel | 15W | Vsupply=12V, Rspk = 4Ohm, THD+N <10% |
30W | Vsupply=18V, Rspk = 4Ohm, THD+N <10% | |
44W | Vsupply=24V, Rspk = 4Ohm, THD+N <10% | |
10W | Vsupply=12V, Rspk = 8Ohm, THD+N <10% | |
20W | Vsupply=18V, Rspk = 8Ohm, THD+N <10% | |
38W | Vsupply=24V, Rspk = 8Ohm, THD+N <10% | |
Sample rates | 44.1-192kHz |